CHECK AND TEST 1

Step 1

Unscrew cover of mainboard with a cross-head screwdriver.

Step 2

Remove the clips.

Step 3

Measure resistance of heater from terminal in PCB area.

Step 4

Check the result.

DIAGNOSIS 1

PROCEDURE 1

Step 1

Remove all drawers.

Step 2

Remove all shelves.

Step 3

Remove the vertical partition plate:
a. Insert 2mm slotted screwdriver into the gap;
b.Lever up the cover plate from bottom;

c. Insert 2mm slotted screwdriver into the side gap;
d. Lever up the cover plate from bottom;

e. Pull the bottom end of cover out;
f. Pull the top of the cover out;

g.Take pipes out and pull them into a horizontal position;
h. Push the latch down and lift top out of cavity;

i. Push latch up and pull bottom out of cavity;

j. Pull partition outward and remove partition.

k. View of interior after partition has been removed.

Step 4

Dismantle the air duct.
a. Hold the bottom of air duct;

b. Pull air duct out from below;

c. Disconnect the terminal for fan motor;

d. Disconnect the terminal of freezer temp. sensor;

e. Remove air duct.

CHECK AND TEST 2

Step 1

Check to see if terminal is full of foam.
If yes, use tweezers to remove foam

Step 2

Ensure terminals behind freezer air duct are properly inserted.

Step 3

Ensure the connection
with mainboard is well.

Step 4

Press Freezer Temp. button along with Mode button for 5 sec, “0” flashes in freezer temperature area.

Step 5

Press Freezer Temperature button,
1 and 3 will appear in freezer temperature area.

Step 6

When 3 appears, remove finger and select manual defrost.

DIAGNOSIS 2

CHECK AND TEST 3

Step 1

Use wire to connect the 2 ends of terminal behind freezer air duct.

Step 2

Use multimeter to check whether the connection of wires is good or not.

DIAGNOSIS 3

CHECK AND TEST 4

Step 1

Check if wires for defrost heater are broken or not.

DIAGNOSIS 4

PROCEDURE 2

Step 1

Cut off the wire.

Step 2

Peel off the sleeves.

Step 3

Ensure proper wire order and connect.

 

Step 4

Tin soldering.

Step 5

Cover point of connection with electrical tape.

CHECK AND TEST 5

Step 1

Measure the resistance of heater from terminal in freezer.

DIAGNOSIS 5

PROCEDURE 3

Step 1

Disconnect the terminals of heater.

Step 2

Use screwdriver to remove the heat conductor.

Step 3

Use 6mm cross-head screwdriver to unscrew on the right and left sides.

Step 4

Lift evaporator and heater up 20mm. The bottom of refrigerator must be higher than the edge of water trough.

WARNING!
Be careful not to deform pipes in red square during step 4.

Step 5

Loosen the clips for fastening heater. There are 8 clips in total.

Step 6

Remove the heater.
REVERSE THE ABOVE PROCESS TO REINSTALL THE HEATER.

CHECK AND TEST 6

Step 1

Reconnect all terminals behind freezer air duct.

Step 2

Ensure the connection
with mainboard is well.

Step 3

Press Freezer Temp. button along with Mode button for 5 sec, “0” flashes in freezer temperature area.

Step 4

Press Freezer Temperature button,
1 and 3 will appear in freezer temperature area.

Step 5

When 3 appears, remove finger and select manual defrost.

DIAGNOSIS 6

PROCEDURE 4

Tip 1

When re-installing the air duct, move the wires out of the way so that they won’t be crushed by air duct.

Tip 2

After pushing the air duct into its position, there should be a sound of click. If no, redo it again.

Tip 3

Check to see if there is a wide gap between air duct and cabinet.
IF SO, install air duct again.

Tip 4

Ensure that latches are properly inserted into cavities.

Tip 5

First, insert top of cover plate into the gap. Then, bend plate to insert the bottom. Lastly, snap middle into place.

PROCEDURE 5

Step 1

Push a 6mm sucker onto display and turn the knob to strengthen suction force.

Step 2

Attach strap to knob to facilitate pulling out display board.

Tips for proper installation of display:

Tip 1

After connecting terminal, please tape wires in place to prevent crushing by the cover.

Tip 2

After inserting display into cavity, press edge until you hear a clicking sound, this means the board is pushed properly into final position.
Please press all buttons on display board to make sure display functions properly.

PROCEDURE 6

Step 1

Lever off the cover on door cap.

Step 2

Remove the screws (in total 2).

Step 3

Pull out the plastic;

Step 4

Disconnect the terminal for display panel.

Step 5

Remove tape.

Step 6

Push display out by the corner.

Reverse above steps to install display board. Follow tips carefully:

Tip 1

Please press all buttons on display board to verify if it is working properly. Make sure all words and icons are clear.

PROCEDURE 7

Step 1

Unscrew cover of mainboard with a Cross-head screwdriver.

Step 2

Remove the clips.

Step 3

Disconnect terminals.

Step 4

Unscrew the mainboard.

Step 5

Pull out the buckle to
remove the mainboard.

DIAGNOSIS 5

GO BACK TO COMPONENT LIST